Make My Space
Kitchens

Hob and Chimney Niche Materials: What Survives Heat, Grease and Steam

Which materials belong behind the hob, under it and around the chimney? Backsplash, heat shields, side panels, ducting and clearances for Indian kitchens.

By Make My Space7 min read

Share
Charcoal kitchen with stone hob wall and chimney niche
Charcoal kitchen with stone hob wall and chimney niche
In this guide 9 sections

The few feet around your hob take more punishment than the rest of the kitchen put together. Woodage (Aug 2026) notes that oil spattering from a tadka can reach 220 °C, and it lands alongside turmeric, chilli and steam from the pressure cooker.

When this zone fails, the culprit is usually the wall behind, the board under the hob, the panel beside the hood or a swollen duct cut-out. Here is what each part should be made of.

The Hob Zone at a Glance

Part of the nicheWhat it facesChooseAvoid
Wall behind the hobDirect heat, oil spatter, spice stainsStainless steel sheet, back-painted glass, large-format tile with epoxy grout, granite or quartz slabPVC, polystyrene, MDF/HDF or wood panels, acrylic cladding
Under a built-in hobTrapped heat from the burnersA ventilated, removable heat-resistant separator plateAn open drawer directly under the hob
Shutters near the burnersRadiant heat and greaseHeat-tolerant finishes, kept at the maker's clearanceHeat-sensitive finishes right beside the burners
Panels beside the chimneyThe worst heat and grease in the kitchenMoisture-resistant board, finished and edge-banded on every exposed faceMDF, unfinished sides
Duct and loft cut-outsHot, greasy, steamy airFactory-cut, sealed edges; rigid or GI ductSite jigsaw holes through raw board

Sources: Woodage backsplash guide (Aug 2026); Material Depot; SurajWood; KKT Kolbe and Howdens installation guides; WizzyBuilds chimney guide (Aug 2026).

The Wall Behind the Hob

Here looks must come second. Material Depot says never to use decorative panels directly behind the cooktop. Polystyrene is a fire risk, PVC softens and warps in burner heat, MDF and HDF let oil seep in and warp, and wood louvers soak up oil in their grooves. Even premium acrylic panels are not meant for this wall. SurajWood recommends a glass or tiled backsplash behind the hob instead.

What works:

  • Stainless steel sheet: Woodage calls a 1.0–1.5 mm SS 304 panel the best-performing backsplash for heavy Indian cooking. It is grout-free and non-porous, though it can look industrial.
  • Back-painted glass: A single 6–8 mm panel in any colour, grout-free and heat-tolerant. Woodage rates it excellent for the hob zone. Make sure the glass is toughened.
  • Large-format vitrified tile: A 600 × 1,200 mm tile has very few joints. Use epoxy grout, as cement grout soaks up oil and turmeric.
  • Granite or quartz slab: Material Depot lists stone as a premium heat-resistant choice behind the cooktop. Natural stone needs sealing.

Watch out for: Glass mosaic behind the hob. Woodage notes it packs in roughly 10 linear metres of grout per square foot, so keep it for the sink wall.

Under the Hob: The Heat Shield

A built-in hob's underside gets hot, and manufacturers are specific about what goes below it. KKT Kolbe's installation manual asks for a protective plate of heat-resistant material, such as perforated sheet metal for ventilation, at least 50 mm below the hob when there is a drawer underneath. Any adhesive used must withstand 150 °C. Howdens specifies a 6 mm heat-resistant separator plate that lets the hob breathe and can be removed for servicing.

Watch out for:

  • Cutlery drawers fitted tight under the hob. Howdens notes that a separator plate may rule out some internal drawer sets, so plan the base unit with the hob model in hand.
  • Blocked ventilation. Always follow the gap in your hob's own manual.
  • Raw cut-out edges. Seal the counter and carcass edges around the hob so steam and spills cannot get in.

The unit below the hob often doubles as LPG storage. WizzyBuilds suggests a ventilated, louvred base unit about 600 × 600 mm for the cylinder, with the gas pipe left exposed and the valve at least 100 mm above the platform.

Shutters and Side Panels Next to the Hob

Shutter finishes differ in how much heat they tolerate. SurajWood, an acrylic panel maker, advises keeping its acrylic shutters at least 600 mm horizontally from gas burners and 300 mm from electric hobs. Ask for the same clearance figure for whichever finish you choose.

The chimney end panels are worse off. WizzyBuilds says the side panels beside the hood take the most heat and grease in the kitchen. They should never be MDF, and every exposed face and edge should be properly finished and banded, not left as raw board.

The Chimney Opening and Wall Units

Getting height and gaps right protects the cabinets as well as suction.

  • Height: WizzyBuilds suggests 610–760 mm above a gas hob, with 660–710 mm as the sweet spot, and 500–610 mm for induction. Woodage gives 650–750 mm for gas.
  • Clearance: Leave 50–75 mm on each side of the hood. A 900 mm chimney needs an opening of about 950–1,050 mm (WizzyBuilds).
  • Depth: A hood around 500 mm deep sticks out 150–200 mm beyond 300–350 mm wall units, so the flanking units need finished side faces.
  • Height conflict: Wall units usually hang 450–600 mm above the counter, below the chimney height. Plan for shorter units beside the hood, or a raised run, at design stage.

Ducting and the Loft Above

The duct carries hot, greasy, wet air through your cabinetry. WizzyBuilds recommends a 150 mm duct for a 60 cm chimney and 200 mm for 90 cm. It warns that a duct box inside a loft eats 200–250 mm of depth and that "a jigsaw hole through raw board is where swelling starts". Duct cut-outs in the carcass or loft should be cut and edged in the factory.

Woodage compares duct materials: flexible aluminium, rigid PVC, semi-rigid, and GI, which it rates the most durable and fire-safe. It also recommends sealing joints with foil tape rather than insulation tape, fitting an external cap with a backdraft flap and keeping access for cleaning. For power, WizzyBuilds puts a 6A socket at about 2,200–2,400 mm, hidden behind the flue cover.

What Hob-Zone Materials Cost in 2026

Published figures vary by city and specification:

  • SS 304 backsplash panel: ₹300–700 per sq ft installed (Woodage, Delhi NCR, prices verified May 2026).
  • Back-painted glass panel: ₹380–750 per sq ft installed (Woodage, May 2026).
  • Large-format tile (600 × 1,200 mm): ₹110–420 per sq ft installed (Woodage, May 2026).
  • Chimney hood (60 cm): about ₹6,000–12,000 entry level, ₹13,000–26,000 for the sweet spot, and ₹40,000+ premium (WizzyBuilds, August 2026).

How Make My Space Approaches It

At Make My Space, our standard carcasses are built in BWP plywood, which suits the steam and spills around the hob and sink. A premium aluminium kitchen option is also available. Projects are completed in 45 days and backed by a 10-year warranty, with modular kitchens starting from ₹3.5 lakh and full home interiors starting from ₹10 lakh.

FAQ

What is the best material behind a gas hob?

A non-porous, heat-tolerant surface with few joints, such as an SS 304 sheet, toughened back-painted glass, large-format tile with epoxy grout, or a stone slab.

Can I use PVC or acrylic panels behind the hob?

No. PVC softens with heat, and acrylic panel makers themselves recommend glass or tile directly behind the hob.

Do I need a heat shield under a built-in hob?

If there is a drawer or storage directly below, yes. Follow your hob manual. KKT Kolbe asks for a ventilated plate at least 50 mm below the hob.

How high should the chimney be above the hob?

About 650–750 mm above a gas hob, and lower for induction, but always check your chimney maker's figure.

Which duct material is best for a kitchen chimney?

Woodage rates GI duct as the most durable and fire-safe. Whatever you use, keep runs short and seal joints with foil tape.


Planning a kitchen in Raipur? See our modular kitchens in Raipur.

hob chimney niche materialsmaterial behind gas hobkitchen chimney side panelhob heat shieldchimney duct material

Share

From the collection

Products in this guide

French-Classic Arched Kitchen

Kitchens · L Kitchen

French-Classic Arched Kitchen

Laminate (ASA, high-gloss, MR+) · Plain PU · Routed 25mm PUHDHMR, Particle board, Plywood, as per finish

L kitchen, classic / traditional — PU uppers + wood Laminate bases shutters, made to measure.

From₹2,400/ sq.ft. + GST

Plan yours

Talk to a designer

Tell us about your space. We will reply with ideas and an itemised estimate, or call +91 75838 37711.

We use your details only to prepare your quotation and contact you about it. See our Privacy policy and Terms.

More on kitchens

WhatsApp